EXTRACTED TEXT FROM: Instructions for BSWF profile+CMY+CTO.docx

Four in one cutting lamp

operation instruction


Please read the instructions carefully before use.Please read the instructions carefully before use.
Please read the instructions carefully before use.
Please read the instructions carefully before use.












catalogue
1. Matters needing attention and installationone
1.1 statementone
1.2 maintenanceone
1.3 Product Precautionsone
1.4 Product introductionone
1.5 signal line connection2
1.6 Installation of lamps2
2 control panelfour
2.1 key descriptionfour
2.2 main menufive
2.2.1 Settingsfive
3-channel functionsix
3.1 channel tablesix
4 Common faultsone0


Precautions and installation
statement
Thank you for choosing our products! This product is in good condition and the packaging is complete when it leaves the factory. For your safe and effective use of this product, please read this instruction carefully and completely before using this product. This instruction manual contains important information for installation and use. Please follow the instructions for installation and operation. At the same time, please take good care of this instruction manual for use from time to time. Our company is not responsible for the damage to lamps or other performance caused by personal failure to follow the instructions during installation, use or maintenance.
This manual is subject to technical changes without prior notice.
maintain
Disconnect the power supply before maintenance.
The lamp tube should be kept dry to avoid working in wet environment.
Intermittent use will effectively prolong the service life of lamps.
In order to prolong the service life of lamps, please clean the fan, fan net and lens frequently.
Do not rub the lamp housing with organic solvents such as alcohol to avoid damage.
Precautions for products
This lamp is for professional use only.
Ensure that the power supply voltage is consistent with the equipment requirements before operation.
Do not place this product where it is easy to loosen or shake.
In the process of use, if the lamp is abnormal, stop using the lamp in time.
In order to ensure the service life of the product, the product should not be placed in a damp or leaking place, nor should it work in an environment where the temperature exceeds 60 degrees.
After the power failure, it takes 20 minutes to completely cool the lamp before using the power supply again.
The rotating parts of lamps and lanterns and the attached accessories must be inspected regularly. If it is loose and shaking, it should be reinforced in time to prevent accidents.
To ensure the normal use of this product, please read the instructions carefully.
Product introduction
Power of light source:
Power supply: AC 200V~240V/50~60Hz;
Color wheel 1: each color wheel consists of 5 color wheels+white light;
Color wheel 2: includes cmyfunction;
Color wheel 3: contains CTO function
Pattern plate: 6 patterns+white circle;
Glass pattern: 7 patterns+white circle;
540 translation and 270 inclination;
Overheating protection;
Control mode: DMX512/ master-slave/automatic;
IP20 protection level

Signal wire connection
Lamps and lanterns have standard DMX input and output 3-core or 5-core XLR sockets. Use the shielded twisted pair signal line specially designed for DMX 512; Signal lines are generally connected at 150 meters, and DMX512 signal amplifier must be added for long-distance signal transmission.
Connect the shielded twisted pair signal line from the DMX socket of the controller to the DMX input of the first device, from the DMX socket of the first device to the DMX input of the second device, and so on until all the lights are connected. Then install a terminal plug on the 3-core jack of the last connected lamp outlet on each circuit. (Weld a 4/1W, 120Ω resistor between pins 2 and 3 of the 3-pin cannon plug).


Important: The wires should not touch each other or the metal casing.



Fig. 1 schematic diagram of DMX signal line connection



Calculation method of starting address code of lamps;

The initial address code of the current lamp is equal to (the initial address code of the previous lamp) (the number of channels of the lamp)
1: The starting address code value A001 of the first lamp.

2. The number of basic channels of the controller should be greater than or equal to the total number of channels used by the lamp.

3. Note: When using any controller, each lamp should have its own initial address code. If the initial address code of the first lamp is set to 001, the number of lamp channels is 24CH; Then the beginning of the second lamp address code is set to 025; The initial address code of the third lamp is set to 050; And so on (this setting also needs to be determined according to different control platforms).

fix

Lamps can be placed horizontally, obliquely and upside down. Pay attention to the installation method when hanging obliquely and upside down.
As shown in Figure 2, before positioning the lamps, the stability of the installation site must be ensured. When installing the reverse suspension, it must be ensured that the lamp will not fall on the support frame. Safety ropes passing through the support frame and auxiliary suspended light handles must be used to ensure safety. Prevent lamps from falling and sliding.
.
When installing and debugging lamps, pedestrians are forbidden to pass under them. Regularly check whether the safety rope is worn and whether the hook screw is loose.

Our company will not take any responsibility for all the consequences caused by the unstable installation of chandeliers.


Schematic diagram of upside-down lamp
















control panel

2.1 key description

Figure 3 Schematic diagram of key descriptions on the panel

Take "Modify DMX Address Code" as an example to introduce the usage of keys:

1. If it is not the main interface at present, press the "Left" key (one or more times) to return to the main interface.

2. In the main interface, press the "Up" key or the "Down" key to select the "DMX Settings" button.

3. Press "OK" key to enter "DMX Settings" interface.

4. Press the "Up" or "Down" key to modify the DMX address code.

5. Press "OK" to exit the editing status.

6. Right click on the main interface to enter the shortcut key of calibration interface.

7. Note: The shortcut keys at the bottom of the main interface, Chinese/English, screen hovering and reset, can only be touched manually, but not pressed.






2.2.1DMX settings

Key description: press up or down to 1 or -1 mode; Right click is next; Press the left and confirm button to save and exit.
2.2.2 Menu
First-level menu
Secondary menu
Three-level menu
Four-level menu
Five-level menu

DMX settings
DMX address
1 - 512




Channel mode
24CH




operational mode
DMX





automatic





sound-controlled



Effect setting
Horizontal reversal
no





be




T vertical inversion
no





be




Vertical feedback
close





open




Dimming curve
straight line





Square law





Inverse square law





S- curve




Dimming frequency
600 Hz





1200





2400 Hz





4800 Hz





9600 Hz





12,000 Hz





24,000 Hz




No signal mode
Fade to Black





keep




Master-slave mode
From the machine





M host




Acoustic sensitivity
10 - 100



display setting
Display direction
Normal/normal





Rotate 180/rotate 180




Display brightness
1-100




Temperature unit
°C





°F




language
English





Chinese



Motor reset
department
no





be




perpendicular/vertical
no





be




head
no





be



Manual control
level
0 - 255




. . .
0 - 255




Function setting
0 - 255



MX reality
level
0 - 255




. . .
0 - 255




Function setting
0 - 255



service
password
rectify
Motor calibration
level
-128 -> 127




. . .
-128 -> 127


Restore factory settings
no





Channel table:
passage
function
Channel value
effect
35 channel



one
Pan/level
000
-
255
0-100%
2
PanFine/horizontal fine adjustment
000
-
255
0-100%
three
Tilt/vertical
000
-
255
0-100%
four
TiltFine/vertical fine adjustment
000
-
255
0-100%
five
PanTiltSpeed/horizontal vertical speed
000
-
255
Horizontal vertical speed, fast to slow
six
Strobe/strobe
000
-
009
consecrate


010
-
199
Synchronous strobe is slow to fast.


200
-
249
Asynchronous strobe is slow to fast.


250
-
255
consecrate
seven
Dimmer/dimming
000
-
255
Dimming from 0% to 100%
eight
Cyan/cyan
000
-
255
From shallow to deep
nine
Magenta/magenta
000
-
255
From shallow to deep
10
Yellow/yellow
000
-
255
From shallow to deep
11
CTO/color temperature
000
-
255
From shallow to deep
twelve
Colour1/color wheel 1
000
-
009
white light


010
-
019
Color 1


020
-
029
Color 2


030
-
039
Color 3


040
-
049
Color 4


050
-
059
Color 5


060
-
069
Color 5+ color 4


070
-
079
Color 4+ Color 3


080
-
089
Color 3+ Color 2


090
-
099
Color 2+ Color 1


100
-
109
Color 1+ white light


110
-
255
Turn slowly to fast.
13
CRI/demonstrative finger
000
-
127
white light


128
-
255
Finger cutting
14
FixGobo/fixed pattern
000
-
009
white light


010
-
019
Pattern 1


020
-
029
Pattern 2


030
-
039
Pattern 3


040
-
049
Pattern 4


050
-
059
Pattern 5


060
-
069
Pattern 6


070
-
079
Pattern 1 jitter from slow to fast.


080
-
089
Pattern 2 jitter from slow to fast.


090
-
099
Pattern 3 jitter from slow to fast.


100
-
109
Pattern 4 jitter from slow to fast.


110
-
119
Pattern 5 jitter from slow to fast.


120
-
129
Pattern 6 jitter from slow to fast.


130
-
191
Turn fast to slow.


192
-
255
Reverse slowly to quickly.
15
RotGobo/rotating pattern
000
-
009
white light


010
-
019
Pattern 1


020
-
029
Pattern 2


030
-
039
Pattern 3


040
-
049
Pattern 4


050
-
059
Pattern 5


060
-
069
Pattern 6


070
-
079
Pattern 7


080
-
089
Pattern 1 jitter from slow to fast.


090
-
099
Pattern 2 jitter from slow to fast.


100
-
109
Pattern 3 jitter from slow to fast.


110
-
119
Pattern 4 jitter from slow to fast.


120
-
129
Pattern 5 jitter from slow to fast.


130
-
139
Pattern 6 jitter from slow to fast.


140
-
149
Pattern 7 jitter from slow to fast.


150
-
190
Turn fast to slow.


191
-
192
stop


193
-
255
Reverse slowly to quickly.
16
GoboRot/pattern rotation
000
-
127
Pattern angle adjustment


128
-
190
The pattern is turning fast to slow.


191
-
192
stop


193
-
255
Pattern inversion is slow to fast.
17
Animation Disk/effect pattern
000
-
009
white light


010
-
127
Linear pattern


128
-
255
Pattern jitter is slow to fast.
18
Zoom/zoom
000
-
255
0-100%
19
Focus/focusing
000
-
255
0-100%
twenty
Focus Fine/focus fine adjustment
000
-
255
0-100%
21
Prism/prism
000
-
127
Prismatic


128
-
255
Prism cut in
22
PrismRot/prism rotation
000
-
127
Prism angle adjustment


128
-
187
The prism is turning slowly to fast.


188
-
195
Prism rotation stops


196
-
255
Prism reversal is slow to fast.
23
Frost/atomization
000
-
003
No atomization


004
-
255
Linear atomization
24
Framing Macro/cutting macro
000
-
009
No function


010
-
026
Figure 1


027
-
043
Figure 2


044
-
060
Figure 3


061
-
077
Figure 4


078
-
094
Figure 5


095
-
111
Figure 6


112
-
128
Figure 7


129
-
145
Figure 8


146
-
162
Figure 9


163
-
179
Figure 10


one hundred and eighty 
-
196
Figure 11


197
-
213
Figure 12


214
-
230
Figure 13


231
-
247
Figure 14


248
-
255
Graphics 1-14 automatic switching
25
Framing Up1/Cutting Up 1
000
-
255
0-100%
26
Framing Up2/Cutting Up 2
000
-
255
0-100%
27
Framing Down1/cutting down 1
000
-
255
0-100%
28
Framing Down2/cutting down 2
000
-
255
0-100%
29
Framing Left1/cutting left1
000
-
255
0-100%
thirty
Framing Left2/cutting left2
000
-
255
0-100%
31
Framing Right1/cutting right 1
000
-
255
0-100%
32
Framing Right2/cutting right 2
000
-
255
0-100%
33
Framing Rota/cutting rotation
000
-
255
0-100%
34
Iris/aperture
000
-
127
Linear aperture


128
-
159
Aperture fast forward and slow out.


160
-
191
Aperture enters slowly and exits quickly.


192
-
255
Aperture fast-forward and fast-out
35
Function/function
210
-
215
XY reset, hold for 3S.


220
-
235
Head motor is reset for 3S.


240
-
255
All motors are reset for 3S.



Common faults
According to some common faults, the corresponding solutions are put forward. Any problem that cannot be solved should be handled by professionals. Disconnect the lamp before servicing it.
After a normal reset, the lamp will not accept control from the console.
Check whether the digital starting address value and function options of lamps and lanterns are correct;
Check whether the communication control line is connected correctly, whether the communication line is too long or interrupted;
Check whether the control equipment is invalid and whether the serial access signal amplifier is invalid;
Check whether the communication line is too long or other equipment interferes with each other;
Optimize wiring, shorten the length of control signal line, and wire the high and low voltage lines separately;
Add a signal amplifier;
The signal line adopts high-quality shielded twisted pair;
Connect the signal terminal resistor (120 ohm) at the end of the lamp.

Lamps can't start.
Check whether the power parameters are consistent with the lamps;
Check the poor contact caused by extrusion deformation, vibration, damp internal parts and other reasons during long-distance transportation.
Or fall.
Please check whether the internal integrated wire connector of the lamp falls off or is loose.
Check whether the electronic components of the lamp tube (such as electronic transformer, PCB board, motor control board, etc.) are loose, short-circuited and burned.

When working, the X-axis or Y-axis action of the lamp is abnormal.
Check one by one according to the previous step;
Check whether the transmission belt corresponding to the X and Y axis directions in the lamp tube falls off or breaks;
Check whether the data feedback receiver (optical coupler) corresponding to the X and Y directions in the lamp is damaged;
Restart the machine and reset it once.
